1983 Westsail 39’ Project Boat
Yes, we’d sell for $75,000 but we have to be open to any written offers until the end of May.Money goes back into the program for future projects.Great offshore capable Bob Perry designed sailboat.This boat has been extensively refit over the past two years. Project, you ask?Yes, it’s about 90% complete.
1983 Westsail 39’ Project Boat
Yes, we’d sell for $75,000 but we have to be open to any written offers until the end of May.Money goes back into the program for future projects.Great offshore capable Bob Perry designed sailboat.This boat has been extensively refit over the past two years. Project, you ask?Yes, it’s about 90% complete. This vessel was used as a training platform during Covid when our students couldn’t complete all of the required field experience for their degrees.
Boat NameKing's Pride
DimensionsLOA: 39 ft 0 in
Beam: 13 ft 0 in
AccommodationsNumber of heads: 1
Additional Information$75,000
Up for Auction, 1983 Westsail 39’ Project Boat
Yes, we’d sell for $75,000 but we have to be open to any written offers until the end of May.
Money goes back into the program for future projects.
Great offshore capable Bob Perry designed sailboat.
This boat has been extensively refit over the past two years. Project, you ask?
Yes, it’s about 90% complete. This vessel was used as a training platform during Covid when our students couldn’t complete all of the required field experience for their degrees.
We invested well over $100,000 in this project! Our mission was accomplished, and we have a bunch of students graduating in June and employed in the marine trades. Great opportunity for someone, but it is still a PROJECT. We have over 60 videos on YouTube, so that’s a great place to start. Check out the “Offshore” videos SVC Skallywags
Open Boat tours scheduled for May 19,20,21 Information about how to bid, cost spreadsheet, blog, photos are posted at cruiserscollege.org
What’s been done?
- $20,000 in the rig with a donated paint job. Including all new wiring, hardware, standing rigging, halyards, lights, wind instrument, windex, and Harken roller furler
- All new drivetrain: Yanmar 45 hp 4JH, down angle gear box, new shaft, shaft tube, packing gland, stern bearing, & 4 blade 18” Max prop, new water-lift muffler, & entire exhaust hose
- Fuel tanks removed, inspection ports added, tested, new fill/vent hoses, stripping port added for fuel sampling, extra port for future use (maybe diesel furnace)
- Rudder removed, inspected, new Edson radial drive, new cables, new rudder stops
- Redesigned bilge, new bilge pumps, double bottom with closed cell foam, emergency portable pump
- Bottom was water-blasted, faired, barrier coated and will have new bottom paint just before launch
- New head installed, cleaned holding tank, all new hoses, discharge pump, shower sump discharge pump
- Re-designed propane locker, new hose, new control/sniffer, new Force 10 stove/oven
- Keel cooled refrigeration installed with evaporator for freezer and spill-over thermostat/fan system for refrigerator, system has great insulation and will be super-efficient.
- New electrical system: Dual hull inlets so the vessel can be plugged in anywhere in the world, All new wire
- Complete Victron system including: Multiplus 3000 inverter, 400 aH of Victron lithium batteries, DC to DC chargers for start & windlass batteries (AGM’s), Solar controller, New AC/DC panels and circuits
- 170 amp Balmar alternator & WakeSpeed WS500 regulator
- Windlass removed, serviced, new wiring, foot switches, & relay
- New windows made & installed
- NMEA 2000 backbone installed, wind, depth, temperature transducers installed
As much as possible, every system was designed to be serviced, inspected, & easy to maintain
Work still needed, project boat:
- Some Woodwork, painting, trim, cap & hand rail re-finishing
- Canvas, headsail, lower running rigging, and vang/preventers
- Hot water heater, small plumbing projects
- Chartplotter/Radar, VHF
- Boat was set up for hydrovane, but it was sold, replace if desired
- Electrical: Mostly complete, some circuits need to be finished
- I’m sure we’ve missed a few things….
Contact Michael Beemer, SVC Department chair for more information or to submit a bid
1019 Q Ave
Ste A & B
Anacortes, WA 98221 United States
Toll-freeTel
Email Us
